Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. A running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward bearings of a nave
   9.5. A forward bottom frame
   9.6. A forward rack
   9.7. The stabilizer of cross-section stability of a forward suspension bracket
   9.8. The bottom lever of a forward suspension bracket
   9.9. Replacement of the bottom hinge of a forward suspension bracket
   9.10. A back nave
   9.11. A back rack
   9.12. The stabilizer of cross-section stability of a back suspension bracket
   9.13. The top lever of a back suspension bracket
   9.14. The bottom lever of a back suspension bracket
   9.15. A steering wheel
   9.16. A steering column
   9.17. An intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. The pump of the amplifier of a steering
   9.21. Removal of air from system of a steering with the amplifier
   9.22. A tip of steering draught
   9.23. Steering draught
   9.24. Corners of installation of wheels
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions



9.6. A forward rack
THE GENERAL DATA

Details of a forward rack

Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports. Remove a corresponding forward wheel.
2. Unscrew a nut and disconnect draught of the stabilizer of cross-section stability for a forward rack.
3. Disconnect a brake hose from an arm on a forward rack.
4. Disconnect wires of the gauge of deterioration brake колодок from a forward rack.
5. Note rack position on a rotary fist.
6. Unscrew two bolts of fastening of a rotary fist to a forward rack.
7. Unscrew bolts of fastening of a rotary fist to a forward rack.
8. Take a bolt of fastening of a rotary fist to a forward rack.
9. Take the top part of a rotary fist from a rack and establish a rotary fist on a support.
10. In a motor compartment remove a protective plastic cap from the top part of a forward rack.
11. Unscrew a nut of fastening of the top part of a rack. Thus keep a rod of a forward rack from проворачивания a wrench.
12. Remove a nut of fastening of the top part of a forward rack.
13. Remove the top support of a forward rack.
14. Lower a rack and take from under a forward wing.

Repair of a forward rack

The forward rack which has been removed from the car


PERFORMANCE ORDER
1. Using the special adaptation, compress a spring so that it has departed from the top part. At use of the special adaptation for compression of springs watch, that spring coils were reliably grasped also spring compression make from opposite sides.

The prevention

The spring has very big effort of compression, therefore use only very reliable tool. At all do not connect a spring a wire.


2. Fix a key a rod of the shock-absorber from проворачивания and, using the second накидной a key, unscrew the central nut of fastening of a rod of the shock-absorber.
3. Remove the top ring with the bearing.
4. Remove top гнедо springs.
5. Remove the buffer.
6. Remove a spring from a forward rack.
7. Check up all elements of a forward rack on deterioration, damages or deformation. Check up smoothness of a course of a rod of the shock-absorber. Check up the shock-absorber on tightness, and also its rod on dot corrosion on all length.
8. Establish a cylindrical spring so that its bottom end has correctly settled down in the bottom nest of a spring.
9. Establish the buffer, top гнедо springs and the top ring with the bearing.
10. Screw a nut on a rod of the shock-absorber and tighten its demanded moment, thus keep a rod from проворачивания the second wrench.
11. Slowly ослабьте the tool for spring compression. Check up that extreme coils of a spring have correctly settled down in spring nests.

Installation

Installation is made in sequence, return to removal.