Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. A running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward bearings of a nave
   9.5. A forward bottom frame
   9.6. A forward rack
   9.7. The stabilizer of cross-section stability of a forward suspension bracket
   9.8. The bottom lever of a forward suspension bracket
   9.9. Replacement of the bottom hinge of a forward suspension bracket
   9.10. A back nave
   9.11. A back rack
   9.12. The stabilizer of cross-section stability of a back suspension bracket
   9.13. The top lever of a back suspension bracket
   9.14. The bottom lever of a back suspension bracket
   9.15. A steering wheel
   9.16. A steering column
   9.17. An intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. The pump of the amplifier of a steering
   9.21. Removal of air from system of a steering with the amplifier
   9.22. A tip of steering draught
   9.23. Steering draught
   9.24. Corners of installation of wheels
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions


Подробнее: https://welx.net

9.15. A steering wheel

MODELS WITHOUT THE SAFETY PILLOW

PERFORMANCE ORDER
1. Remove a wire of weight from the accumulator.
2. Establish forward wheels for movement directly forward.
3. Remove the button of a sound signal from a steering wheel and disconnect an electric socket.
4. A screw-driver unbend a short moustache of fixing of a nut of fastening of a steering wheel
5. Unscrew a nut of fastening of a steering wheel.
6. Put labels of combination of a steering wheel and a steering shaft.
7. Using a stripper, remove a steering wheel and a spring from a steering shaft.
8. Establish a spring and a steering wheel on шлицы a steering shaft. Thus combine the labels made at removal of a steering wheel.
9. Establish a new spring washer and screw a nut of fastening of a steering wheel, having tightened its demanded moment.
10. A screw-driver unbend a short moustache of fixing of a nut of fastening of a steering wheel.
11. Connect an electric socket to the button of a sound signal and establish the button in the steering wheel centre.
12. Connect the accumulator and check up action of a sound signal.

MODELS WITH THE SAFETY PILLOW

PERFORMANCE ORDER
1. Remove a wire of weight from the accumulator.
The prevention

The further actions make not earlier than in 1 minute that the air cushion condenser was discharged completely.


2. Establish forward wheels for movement directly forward.
3. Unscrew two screws from a back part of a steering wheel.
4. Being careful, remove a safety air cushion.
5. Disconnect an electric socket from a safety pillow.
6. At presence disconnect an electric socket from the switch of management of a radio receiver.
7. A screw-driver unbend a short moustache of fixing of a nut of fastening of a steering wheel. Completely unscrew bolts of fastening of a wheel and remove a wheel.
8. Unscrew and remove a nut of fastening of a steering wheel.
9. Remove a spring washer.
10. Put combination labels on a steering wheel and a steering shaft.
11. Using a stripper, remove a steering wheel from grooves of a steering shaft.
12. At steering wheel removal pass an electrocontrol run a radio receiver through an aperture of a steering shaft.
13. Establish a steering wheel on шлицы a steering shaft and pass through an aperture of a steering wheel of a wire of management of a radio receiver.
14. Establish a washer, screw a nut of fastening of a steering wheel, having tightened its demanded moment. Fix a nut from отворачивания a bending of a uvula of a washer.
15. Connect an electric socket of the switch of management of a radio receiver
16. Establish a safety air cushion, preliminary having connected an electric socket. Fix a pillow screws.
17. Connect the accumulator.