Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. A running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward bearings of a nave
   9.5. A forward bottom frame
   9.6. A forward rack
   9.7. The stabilizer of cross-section stability of a forward suspension bracket
   9.8. The bottom lever of a forward suspension bracket
   9.9. Replacement of the bottom hinge of a forward suspension bracket
   9.10. A back nave
   9.11. A back rack
   9.12. The stabilizer of cross-section stability of a back suspension bracket
   9.13. The top lever of a back suspension bracket
   9.14. The bottom lever of a back suspension bracket
   9.15. A steering wheel
   9.16. A steering column
   9.17. An intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. The pump of the amplifier of a steering
   9.21. Removal of air from system of a steering with the amplifier
   9.22. A tip of steering draught
   9.23. Steering draught
   9.24. Corners of installation of wheels
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions



9.11. A back rack
THE GENERAL DATA

Back rack

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and fix on supports. Remove a corresponding back wheel. Establish a back beam on a support.
2. Remove the protective loose leaf from under an arch of a back wheel.
3. Unscrew a back bolt of fastening of the top part of a back rack.
4. Unscrew a forward bolt of fastening of the top part of a back rack.
5. Take a rack from under a wheel arch.

Repair

Arrangement of a bolt of fastening of a fixing element of a back rack


PERFORMANCE ORDER
1. Using the special adaptation, compress a spring so that its top cup has unloaded.
2. Fix from проворачивания a rod of the shock-absorber a key and, using the second key, unscrew a nut of fastening of a rod of the shock-absorber.
3. Remove a nut of fastening of a rod of the shock-absorber.
4. Remove from a shock-absorber rod the top plate.
5. Remove демпфирующее a ring.
6. Remove a fixing element.
7. Remove the plug.
8. Remove a glass.
9. Remove the buffer and a cylindrical spring.
10. Remove a nest of a spring from a fixing element of a back rack.
11. Check up all elements of an amortisation rack on deterioration, damages or deformation. Check up smoothness of a course of a rod of the shock-absorber. Check up the shock-absorber on tightness, and also its rod on dot corrosion on all length.
12. Establish top гнедо springs in a fixing element of a back rack.
13. Establish on a rod of the shock-absorber the buffer, a glass and the plug.
14. Establish a fixing element of a back rack on a cylindrical spring, and the spring end should settle down in dredging top гнеда springs (arrow).
15. Establish демпфирующее a ring and the top plate.
16. Screw up a nut of fastening of a rod of the shock-absorber, thus keep a rod from проворачивания a wrench.
17. Slowly ослабьте the special tool for spring compression.

Installation

PERFORMANCE ORDER
Installation is made in sequence, return to removal. Tighten bolts of fastening of a fixing element of the top part of a back rack after car installation on wheels.