Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. A running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward bearings of a nave
   9.5. A forward bottom frame
   9.6. A forward rack
   9.7. The stabilizer of cross-section stability of a forward suspension bracket
   9.8. The bottom lever of a forward suspension bracket
   9.9. Replacement of the bottom hinge of a forward suspension bracket
   9.10. A back nave
   9.11. A back rack
   9.12. The stabilizer of cross-section stability of a back suspension bracket
   9.13. The top lever of a back suspension bracket
   9.14. The bottom lever of a back suspension bracket
   9.15. A steering wheel
   9.16. A steering column
   9.17. An intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. The pump of the amplifier of a steering
   9.21. Removal of air from system of a steering with the amplifier
   9.22. A tip of steering draught
   9.23. Steering draught
   9.24. Corners of installation of wheels
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions



9.3. Rotary fists
THE GENERAL DATA

The prevention

At installation of a rotary fist it is necessary to use all new bolts and nuts.


Nave and rotary fist

Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports. Remove a corresponding forward wheel.
2. Unscrew a nut of fastening of steering bent for to a rotary fist. Using a stripper, take the spherical hinge of steering draught from a rotary fist.
3. Unscrew tightening a bolt, крепящий the spherical hinge of the bottom lever of a forward suspension bracket to a rotary fist.
4. Using the lever, move the bottom lever of a forward suspension bracket downwards and take the spherical hinge from a rotary fist. If the pin of the spherical hinge densely sits in a rotary fist, use a screw-driver or a thin chisel as a wedge and expand a clip of fastening of a pin of the spherical hinge.
5. Remove a support, without disconnecting from it a brake hose. Using a soft wire, suspend a support on a forward rack.
6. Unscrew a bolt and remove the gauge of speed of a wheel.
7. Remove a cap of a nut of a nave, take a pin and unscrew a nut of fastening of a power shaft to a nave.
8. Take a power shaft to a nave, taking away a rotary fist from the car.
9. Note position of a rack of a forward suspension bracket on a rotary fist.
10. Unscrew two bolts of fastening of a rack of a forward suspension bracket to a rotary fist. Thus definitively take a power shaft from a rotary fist.
11. Remove a rotary fist.
12. Unscrew the screw and remove a forward brake disk from a nave flange.
13. Unscrew screws (arrows) and remove a mudguard from a rotary fist.

Installation

PERFORMANCE ORDER
1. Establish a mudguard on a rotary fist and fix screws.
2. Establish a brake disk.
3. Check up that шлицы on the external end of a power shaft and grooves in a nave the pure. Pull a nave over power shaft grooves.
4. Pull a rotary fist over a power shaft. Arrange the top part of a rotary fist on a rack and fix bolts.
5. Screw a nut of fastening of a power shaft to a nave and tighten its demanded moment.
6. Establish a support of brakes.
7. Establish a pin of the spherical hinge of the bottom lever of a forward suspension bracket in a rotary fist and fix tightening a bolt.
8. Establish steering draught.
9. Establish a wheel and lower the car.
10. In some stages tighten a nut of fastening of a power shaft to a nave and fix its pin.
11. Establish a cap of a nut of fastening of a power shaft to a nave.
12. Check up and, if necessary, adjust corners of installation of wheels.