Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
- 9. A running gear
   9.1. Introduction
   9.2. Technical characteristics
   9.3. Rotary fists
   9.4. Replacement of forward bearings of a nave
   9.5. A forward bottom frame
   9.6. A forward rack
   9.7. The stabilizer of cross-section stability of a forward suspension bracket
   9.8. The bottom lever of a forward suspension bracket
   9.9. Replacement of the bottom hinge of a forward suspension bracket
   9.10. A back nave
   9.11. A back rack
   9.12. The stabilizer of cross-section stability of a back suspension bracket
   9.13. The top lever of a back suspension bracket
   9.14. The bottom lever of a back suspension bracket
   9.15. A steering wheel
   9.16. A steering column
   9.17. An intermediate shaft of a steering column
   9.18. Replacement of protective covers of steering transfer
   9.19. Steering transfer
   + 9.20. The pump of the amplifier of a steering
   9.21. Removal of air from system of a steering with the amplifier
   9.22. A tip of steering draught
   9.23. Steering draught
   9.24. Corners of installation of wheels
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions



9.5. A forward bottom frame
THE GENERAL DATA

Arrangement of a forward lateral bolt of fastening of the bottom frame

Removal

PERFORMANCE ORDER
1. Establish wheels for movement directly forward.
2. In car salon unscrew a bolt, крепящий the bottom part of an intermediate shaft of a steering column to a gear wheel of steering transfer. Remove a shaft from a gear wheel and move aside.
3. Using a syringe, pump out a liquid from a tank of the amplifier of a steering.
4. On models with a mechanical transmission disconnect draught of a gear change from a transmission.
5. On models with petrol engines disconnect an electric socket of the gauge of oxygen.
6. Hook on the power unit the load-lifting mechanism and raise so that the weight of the power unit was perceived by the load-lifting mechanism.
7. Remove a lattice of a radiator and, using a wire, connect a radiator with an air reflector.
8. Remove a forward bumper.
9. Lift a forward part of the car and fix on supports. Remove both forward wheels.
10. Unscrew nuts and disconnect draughts of the stabilizer of cross-section stability from forward racks.
11. Remove steering draughts from rotary fists.
12. Unscrew tightening bolts, fastening hinges of the bottom levers of a forward suspension bracket in rotary fists.
13. Using the corresponding lever, move downwards the bottom levers of a forward suspension bracket and take pins of spherical hinges from a rotary fist. If the pin of the spherical hinge sits densely in a rotary fist, use a screw-driver or a thin chisel as a wedge and ослабьте a fastening clip.
14. Remove a reception exhaust pipe.
15. Unscrew three bolts of fastening of a back support of the power unit to a transmission.
16. On models with an air conditioning disconnect pipelines of a central air from the bottom frame.
17. Disconnect pipelines of the amplifier of a steering from the right party of the bottom frame.
18. Using the load-lifting mechanism, support the power unit.
19. Unscrew bolts, fastening a support of the forward unit to the bottom frame.
20. Unscrew bolts of fastening of the bottom frame. Lower the bottom frame a little and unscrew pipelines of the amplifier of a steering from steering transfer.
21. Lower the bottom frame and take from under the car.

Installation

Installation is made in sequence, return to removal.