Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
- 3. Engines
   + 3.1. Repair of engine SOCH established in the car
   + 3.2. Repair of engine DOSH established in the car
   - 3.3. Repair of the diesel engine of 1,7 l established in the car
      3.3.1. Introduction
      3.3.2. Technical characteristics
      3.3.3. Check of pressure of compression
      3.3.4. The top dead point (ВМТ) the piston of the first cylinder
      3.3.5. A cover of a head of the block of cylinders
      3.3.6. A pulley of a cranked shaft
      3.3.7. Casings of a gear belt
      3.3.8. Replacement of a gear belt
      3.3.9. The mechanism of a tension of a gear belt and pulleys
      3.3.10. Replacement of a sealing ring of a cam-shaft
      3.3.11. Check and adjustment of backlashes of valves
      3.3.12. A cam-shaft and pushers
      3.3.13. A head of the block of cylinders
      3.3.14. The oil pallet
      3.3.15. The oil pump
      3.3.16. An oil radiator
      3.3.17. A flywheel
      3.3.18. Replacement of sealing rings of a cranked shaft
      3.3.19. Replacement of support of the power unit
   + 3.4. Repair of the diesel engine of 2,0 l established in the car
   + 3.5. Major repairs of engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions



3.3.7. Casings of a gear belt
THE GENERAL DATA

The drive mechanism timing

1. A gear belt
2. The tension mechanism
3. A bolt of fastening of the mechanism of a tension
4. An axis of the mechanism of a tension
5. A bolt of fastening of the lever of the mechanism of a tension
6. A finger
7. A washer
8. A spring
9. A single pulley
10. A bolt of a single pulley
11. A camshaft pulley
12. A bolt of fastening of a pulley distributive
Shaft
13. A flange of a pulley distributive
Shaft
14. The screw
15. A pulley of a cranked shaft
16. A pin
17. A lining
18. A pulley of the fuel pump
19. A nut
20. A pulley of the oil pump
21. A nut
22. The top casing
23. Consolidation
24. Consolidation
25. The bottom casing
26. Consolidation
27. Consolidation
28. A back casing
29. A bolt
30. A bolt
31. A bolt

Removal

PERFORMANCE ORDER
The top casing
1. Lift a forward part of the car and fix on supports. Remove the right forward wheel.
2. Remove a casing of the air filter.
3. Remove auxiliary приводные belts.
4. On the models equipped with an air conditioning, unscrew a bolt of fastening of the mechanism of a tension drive a belt of the compressor and remove it.
5. Establish under the engine a jack and through wooden брусок raise the engine until all top of the engine will not be perceived by a jack. Unscrew nuts and remove the right suspension bracket of the power unit.
6. Unscrew bolts and remove the top casing of a gear belt together with rubber consolidation.
The bottom casing
7. Remove the top casing of a gear belt.
8. Remove a pulley of a cranked shaft.
9. Unscrew bolts and remove the bottom casing of a gear belt together with rubber consolidation.
Internal casing
10. Remove a gear belt.
11. Remove a camshaft pulley, a pulley of the fuel pump of a high pressure, a single pulley and the tension mechanism.
12. Unscrew bolts and remove an internal casing of a gear belt.

Installation

PERFORMANCE ORDER
Installation is made in sequence, return to removal. Thus check up correctness of an arrangement of rubber linings.