| The engine |
| Diameter of the cylinder |
79 mm
|
| Piston stroke |
86 mm
|
| Working volume |
1668 sm3
|
| Operating procedure of cylinders |
1–3–4–2 (cylinder N1 is from outside a gear belt)
|
| Direction of rotation of a cranked shaft |
Clockwise, if to take a detached view a gear belt
|
| Compression degree |
22:1
|
| The maximum capacity |
60 kw at 4400 rpm
|
| The maximum twisting moment |
168 nanometers at 2400 rpm
|
| Pressure of compression |
18,5 – 34,5 bar
|
| The maximum distinction of pressure of compression between any two cylinders |
1,5 bar
|
| Backlashes of valves: |
| – Inlet the valve |
0,15 mm
|
| – Final the valve |
0,25 mm
|
| Camshaft |
| Люфт |
0,05 – 0,20 mm
|
| As much as possible admissible radial palpation |
0,05 mm
|
| Lifting of a cam of the inlet valve |
8,47 – 8,67 mm
|
| Lifting of a cam of the final valve |
8,57 – 8,77 mm
|
| Working backlash of bearings of a camshaft. |
0,040 – 0,082 mm
|
| Greasing system |
| Is minimum admissible pressure of oil at turns of idling and temperature of the engine 80 ° With |
2,0 bar
|
| Backlash between an external rotor of the pump and the pump case |
0,24 – 0,36 mm
|
| Backlash between an internal and external rotor |
0,13 – 0,15 mm
|
| Axial люфт rotors |
0,035 – 0,1 mm
|
| The tightening moments |
| Nuts of fastening of covers of bearings of a camshaft |
19 Nanometers
|
| Bolts of fastening of a cover of a head of the block of cylinders |
8 Nanometers
|
| Bolt of fastening of a pulley of a camshaft |
10 Nanometers
|
| Bolts of fastening of the water pump |
20 Nanometers
|
| Bolts of fastening of a pulley of the water pump |
10 Nanometers
|
| Cover of the bearing of the bottom head of a rod: |
| – A stage 1 |
25 Nanometers
|
| – A stage 2 |
To tighten on a corner 100 °
|
| – A stage 3 |
To tighten on a corner 15 °
|
| Bolts of fastening of a pulley of a cranked shaft |
20 Nanometers
|
| Bolts of fastening of the case of a back sealing ring of a cranked shaft |
10 Nanometers
|
| Bolts of fastening of a pulley of a cranked shaft |
196 Nanometers
|
| Bolts of fastening of a head of the block of cylinders: |
| – A stage 1 |
40 Nanometers
|
| – A stage 2 |
To tighten on a corner from 60 to 75 °
|
| – A stage 3 |
To tighten on a corner from 60 to 75 °
|
| Nut of a pulley of the fuel pump |
69 Nanometers
|
| The main bolts of fastening of a cover of bearings |
88 Nanometers
|
| Forward right suspension bracket of the power unit: |
| – Bolts of fastening of a suspension bracket to the engine |
60 Nanometers
|
| – Bolts of fastening of a suspension bracket to the bottom frame |
45 Nanometers
|
| Back support: |
| – Fastening bolts to скобе |
45 Nanometers
|
| – Fastening bolts to the bottom frame |
20 Nanometers
|
| – Fastening bolts to a transmission |
60 Nanometers
|
| Bolts of fastening of a transmission to the engine: |
| – Bolts М8 |
20 Nanometers
|
| – Bolts М10 |
40 Nanometers
|
| – Bolts М12 |
60 Nanometers
|
| Bolts of fastening of a flywheel: |
| – A stage 1 |
30 Nanometers
|
| – A stage 2 |
To tighten on a corner 45 – 60 °
|
|
Bolts of fastening of the central part of an oil radiator |
49 Nanometers
|
| The oil filter |
15 Nanometers
|
| Bolts of fastening of a safety valve of pressure |
40 Nanometers
|
| Screws of fastening of a cover of the oil pump |
10 Nanometers
|
| Bolts of fastening of a pipe маслоприемника |
19 Nanometers
|
| Nut of fastening of a pulley of the oil pump |
44 Nanometers
|
| Bolts of fastening of the oil pallet |
10 Nanometers
|
| Masloslivnaja stopper |
78 Nanometers
|
| Bolts of fastening of a casing of a gear belt |
8 Nanometers
|
| Bolts of fastening of a single pulley of a gear belt |
76 Nanometers
|
| Bolts of fastening of a pulley of the mechanism of a tension of a gear belt |
19 Nanometers
|