Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
- 5. Fuel system
+ 5.1. Fuel system of petrol engines
- 5.2. Fuel systems of the diesel engine
5.2.1. Introduction
5.2.2. Technical characteristics
5.2.3. The air filter and air inlet channels
5.2.4. An accelerator pedal
5.2.5. Filling and prorolling of fuel system
5.2.6. The gauge of level of fuel
5.2.7. A fuel tank
5.2.8. Check and adjustment of the maximum turns
5.2.9. Start of the cold engine
- 5.2.10. Electric knots of system of injection
5.2.10.1. Engines of 1,7 l
5.2.10.2. Engines of 2,0 l
5.2.11. The fuel pump of a high pressure
5.2.12. Check of the moment of injection of fuel
5.2.13. Adjustment of the moment of injection of fuel
5.2.14. Fuel atomizers
5.2.15. Турбонагнетатель
5.2.16. The heat exchanger
5.2.17. An inlet collector
5.2.18. A final collector
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions
|
MEASURING INSTRUMENT OF THE STREAM OF AIR
Removal and installation
PERFORMANCE ORDER
|
1. Switch off ignition and disconnect an electric socket from a measuring instrument of a stream of air. |
|
2. Loosen the collars (are specified by arrows), release a measuring instrument of a stream of air from inlet channels and remove it. |
3. Installation is made in sequence, return to removal. |
|
THE GAUGE OF TEMPERATURE OF AIR
The prevention
On engines of a turbo with a high pressure the gauge of temperature of air is a component of a measuring instrument of a stream of air.
Removal and installation
PERFORMANCE ORDER
|
1. Switch off ignition, disconnect an electric socket and take the gauge from the inlet channel. |
2. Installation is made in sequence, return to removal. |
|
THE GAUGE OF POSITION OF THE PEDAL OF THE ACCELERATOR
Removal and installation
PERFORMANCE ORDER
|
1. In car salon unscrew clips and remove furnish of the bottom part of the panel of devices from outside the driver. |
2. Disconnect an electric socket from the gauge which is located on the top part of a pedal. |
3. Remove скобу the spherical hinge of draught and remove draught from the gauge. |
|
4. Unscrew screws and remove the gauge from a pedal arm. |
5. Installation is made in sequence, return to removal. |
|
THE GAUGE OF THE CRANKED SHAFT
Removal and installation
PERFORMANCE ORDER
|
1. About Unscrew screws and remove a plastic casing from the top part of a head of the block of cylinders. |
2. For access to the gauge lift a forward part of the car and fix on supports. |
|
3. Disconnect an electric socket of the gauge from a plait of wires. |
|
4. Unscrew a bolt (it is specified by an arrow) and remove the gauge from the block of cylinders. |
5. Installation is made in sequence, return to removal, thus it is necessary to establish a new sealing ring on the gauge. |
|
THE GAUGE OF TEMPERATURE OF THE COOLING LIQUID
The gauge is established from the forward right party of a head of the block of cylinders.
THE GAUGE OF EXCESS OF PRESSURE
Removal and installation
PERFORMANCE ORDER
|
1. Unscrew screws and remove a plastic casing from the top part of a head of the block of cylinders. |
|
2. Unscrew screws, fastening an arm of a plait of wires to the top part of an inlet collector and disconnect an electric socket (it is specified by an arrow) from the gauge of excess of pressure. |
3. Unscrew a bolt and remove the gauge from the top part of an inlet collector. |
4. Installation is made in sequence, return to removal, thus it is necessary to establish a new sealing ring on the gauge. |
|
THE GAUGE OF TEMPERATURE OF OIL
Removal and installation
PERFORMANCE ORDER
|
1. Lift a forward part of the car and fix on supports. |
2. Merge engine oil. Establish a new sealing ring on маслосливную a stopper and screw up it in the oil pallet. |
|
3. Disconnect an electric socket (on a photo) and unscrew the gauge from a forward part of the oil pallet. |
4. Installation is made in sequence, return to removal. Fill in in the engine engine oil. |
|
THE ELECTRONIC CONTROL DEVICE (ECU)
Removal and installation
PERFORMANCE ORDER
|
1. Remove levers of screen wipers and remove a wire of weight from the accumulator. |
2. Unscrew plastic nuts from axes of levers of screen wipers. |
3. Remove rubber consolidation from the top part of a partition of a motor compartment. |
4. Remove a plastic casing from the windscreen basis. |
5. Unscrew nuts and remove a protective casing of block ECU. |
6. Release clamps and disconnect an electric socket from block ECU. |
7. Unscrew nuts and remove block ECU. |
8. Installation is made in sequence, return to removal. |
|
|
|