Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
- 3. Engines
   + 3.1. Repair of engine SOCH established in the car
   + 3.2. Repair of engine DOSH established in the car
   + 3.3. Repair of the diesel engine of 1,7 l established in the car
   + 3.4. Repair of the diesel engine of 2,0 l established in the car
   - 3.5. Major repairs of engines
      3.5.1. Introduction
      + 3.5.2. Technical characteristics
      3.5.3. Removal and installation of the petrol engine together with a transmission
      3.5.4. Removal and installation of the diesel engine together with a transmission
      3.5.5. Engine repair
      3.5.6. Dismantling of a head of the block of cylinders
      3.5.7. Clearing and survey of a head of the block of cylinders
      3.5.8. Assemblage of a head of the block of cylinders
      3.5.9. Removal of pistons from rods
      3.5.10. Removal of a cranked shaft
      3.5.11. The block of cylinders of the engine
      3.5.12. Pistons and rods
      3.5.13. A cranked shaft
      3.5.14. Survey radical and шатунных bearings
      3.5.15. Engine balance of assembly at major repairs
      3.5.16. Installation of piston rings
      3.5.17. A choice of bearings
      3.5.18. Installation of a cranked shaft
      3.5.19. Pistons and rods, check of working backlashes шатунных bearings
      3.5.20. Check of a working backlash of the bearing of the bottom head of a rod
      3.5.21. Installation of pistons with rods
      3.5.22. Start of the engine after major repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions



3.5.10. Removal of a cranked shaft
THE GENERAL DATA

The prevention

At installation of covers of bearings of a cranked shaft it is necessary to use new bolts.


PERFORMANCE ORDER
The petrol engine of 1,6 l
1. Remove the oil pump and a flywheel.
2. Remove pistons and rods.
3. Check up axial люфт a cranked shaft.
4. Mark covers of radical bearings from 1 to 5.
5. Gradually and consistently unscrew bolts of fastening of covers of radical bearings.
6. Remove covers of radical bearings together with loose leaves.
7. Remove a cranked shaft and remove back oil sealing ring of a cranked shaft.
8. Remove the top loose leaves of radical bearings.
Petrol engines of 1,8 and 2,0 l
9. Remove a flywheel and the oil pump.
10. Unscrew screws and remove a partition from the basis of the block of cylinders.
11. In regular intervals and gradually unscrew bolts of fastening of the main block of bearings from the block of cylinders.
12. Remove pistons and rods.
13. Check up axial люфт a cranked shaft.
14. Mark covers of radical bearings from 1 to 5.
15. Gradually and consistently unscrew bolts of fastening of covers of radical bearings.
16. Remove covers of radical bearings together with loose leaves.
17. Remove a cranked shaft and remove back oil sealing ring of a cranked shaft.
18. Remove the top loose leaves of radical bearings.
Diesel engines of 1,7 l
19. Remove a flywheel and unscrew a bolt of fastening of a cover of the oil pump on the right side of the block of cylinders of the engine.
20. Unscrew bolts and remove a back cover of a cranked shaft.
21. Remove pistons and rods.
22. Check up axial люфт a cranked shaft.
23. Mark covers of radical bearings from 1 to 5.
24. Gradually and consistently unscrew bolts of fastening of covers of radical bearings.
25. Remove covers of radical bearings together with loose leaves.
26. Remove a cranked shaft and remove a back oil sealing ring of a cranked shaft.
27. Remove the top loose leaves of radical bearings.
28. Remove the persistent half rings located from two parties of a cover to-rennogo bearing N2.
The diesel engine of 2,0 l
29. Remove an asterisk of a cranked shaft, a chain and a flywheel.
30. In regular intervals and gradually unscrew bolts and remove the main block of bearings from the basis of covers of radical bearings.
31. Remove pistons and rods.
32. Check up axial люфт a cranked shaft.
33. Mark covers of radical bearings from 1 to 5 (on diesel engines of 2,0 l only covers of bearings N1 and 2 have factory marks).
34. Gradually and consistently unscrew bolts of fastening of covers of radical bearings.
35. Remove covers of radical bearings together with loose leaves.
36. Remove a cranked shaft and remove a back oil sealing ring of a cranked shaft. Remove the top loose leaves of radical bearings.