Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
- 3. Engines
   - 3.1. Repair of engine SOCH established in the car
      3.1.1. Introduction
      3.1.2. Technical characteristics
      3.1.3. Check of pressure of compression
      3.1.4. The top dead point (ВМТ) the piston of the first cylinder
      3.1.5. A cover of a head of the block of cylinders
      3.1.6. A pulley of a cranked shaft
      3.1.7. Casings of a gear belt
      3.1.8. A gear belt
      3.1.9. The mechanism of a tension of a gear belt and pulleys
      3.1.10. Replacement of a sealing ring of a cam-shaft
      3.1.11. A cam-shaft and cam-shaft cases
      3.1.12. Hydraulic pushers
      3.1.13. A head of the block of cylinders
      3.1.14. The oil pallet
      3.1.15. The oil pump
      3.1.16. The Flywheel / a drive plate
      3.1.17. Replacement of sealing rings of a cranked shaft
      3.1.18. A suspension bracket of the power unit
   + 3.2. Repair of engine DOSH established in the car
   + 3.3. Repair of the diesel engine of 1,7 l established in the car
   + 3.4. Repair of the diesel engine of 2,0 l established in the car
   + 3.5. Major repairs of engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions



3.1.9. The mechanism of a tension of a gear belt and pulleys

CAMSHAFT PULLEY

Removal

PERFORMANCE ORDER
1. Remove a gear belt.
2. Fix a camshaft from проворачивания one of next ways. Use the special tool made of two steel strips with bolts on the ends which enter into apertures of a pulley of a camshaft.
3. Uncover heads of the block of cylinders and fix from проворачивания a camshaft a wrench for camshaft grooves.
4. Unscrew a bolt of fastening of a pulley of a camshaft and remove a pulley.

Installation

PERFORMANCE ORDER
1. Check up an oil sealing ring of a camshaft on deterioration and damage and, if necessary, replace it.
2. Establish a camshaft pulley. Thus combine an aperture on a pulley (2) with an adjusting pin of a camshaft (1).
3. Tighten a bolt of fastening of a pulley of a cranked shaft the demanded moment. Thus keep a camshaft from проворачивания.
4. Establish a gear belt and a cover of a head of the block of cylinders.

PULLEY OF THE CRANKED SHAFT

Removal

PERFORMANCE ORDER
1. Remove a gear belt.
2. Remove a gear pulley from a cranked shaft.

Installation

PERFORMANCE ORDER
1. Check up that segment шпонка it is located in a groove of a cranked shaft.
2. Combine a groove of a pulley of a cranked shaft with segment шпонкой and establish a pulley on a cranked shaft.
3. Establish a gear belt.

THE TENSION MECHANISM

Removal

PERFORMANCE ORDER
1. Remove a gear belt.
2. Unscrew bolts and remove the tension mechanism in gathering from the case of the oil pump.

Installation

PERFORMANCE ORDER
Establish the mechanism of a tension of a gear belt (1) on a casing of the oil pump. Thus the ledge on a basic plate should be correctly located in an aperture of a casing of the oil pump (2). Tighten bolts of fastening of the mechanism of a tension of a gear belt the demanded moment.