| Type |
The engine c four cylinders, one top camshaft resulted by a gear belt and hydraulic pushers
|
| The engine |
| Engine code |
X16SZR
|
| Diameter of the cylinder |
79 mm
|
| Piston stroke |
81 mm
|
| Working volume |
1598 sm3
|
| Operating procedure of cylinders |
1–3–4–2 (cylinder N1 is located from outside a gear belt)
|
| Direction of rotation of a cranked shaft |
Clockwise (if to take a detached view a gear belt)
|
| Compression degree |
9,6/1
|
| Capacity |
55 kw at 5200 rpm
|
| The maximum twisting moment |
128 Nanometers at 2000 rpm
|
| Pressure of compression: |
| The nominal |
12 – 15 bar
|
| The maximum difference between two any cylinders |
1 bar
|
| Camshaft |
| Axial люфт |
0,09 – 0,21 mm
|
| Lifting of cams: |
| – The inlet valve |
5,61 mm
|
| – The final valve |
6,12 mm
|
| Greasing system |
| Drive of the oil pump directly from a cranked shaft |
| – Is minimum admissible pressure of oil at turns of idling and at the heated-up engine |
1,5 bar
|
| – A backlash between teeths of gear wheels of the pump |
0,08 – 0,15 mm
|
| – Axial люфт |
0,1 – 0,2 mm
|
| Bolts of fastening of a cover of a camshaft |
8 Nanometers
|
| Bolt of fastening of a pulley of a camshaft |
45 Nanometers
|
| Bolt of fastening of a persistent plate of a camshaft |
8 Nanometers
|
| Bolts of fastening of a face cover of a camshaft |
8 Nanometers
|
| Bolts of fastening of a cover of the bottom head of a rod: |
| – A stage 1 |
25 Nanometers
|
| – A stage 2 |
To tighten on a corner 30 °
|
| Bolts of fastening of the water pump |
8 Nanometers
|
| Bolt of a pulley of a cranked shaft: |
| – A stage 1 |
55 Nanometers
|
| – A stage 2 |
To tighten on a corner 45 °
|
| – A stage 3 |
To tighten on a corner 15 °
|
| Bolts of fastening of a head of the block of cylinders: |
| – A stage 1 |
25 Nanometers
|
| – A stage 2 |
To tighten on a corner 60 °
|
| – A stage 3 |
To tighten on a corner 60 °
|
| – A stage 4 |
To tighten on a corner 60 °
|
| Bolts of fastening of a plate of a drive |
60 Nanometers
|
| Forward right suspension bracket of the power unit: |
| – Bolts of fastening of a suspension bracket to the engine |
60 Nanometers
|
| – Bolts of fastening of a suspension bracket to the bottom frame |
45 Nanometers
|
| Back support: |
| – Fastening bolts to скобе |
45 Nanometers
|
| – Fastening bolts to the bottom frame |
20 Nanometers
|
| – Fastening bolts to a transmission |
60 Nanometers
|
| Bolts of fastening of a transmission to the engine: |
| – Bolts М8 |
20 Nanometers
|
| – Bolts М10 |
40 Nanometers
|
| – Bolts М12 |
60 Nanometers
|
| Bolts of fastening of a flywheel: |
| – A stage 1 |
35 Nanometers
|
| – A stage 2 |
To tighten on a corner 30 °
|
| – A stage 3 |
To tighten on a corner 15 °
|
| Bolts of fastening of a radical cover of the bearing: |
| – A stage 1 |
50 Nanometers
|
| – A stage 2 |
To tighten on a corner 45 °
|
| – A stage 3 |
To tighten on a corner 15 °
|
| Bolts of fastening of the oil pump |
8 Nanometers
|
| Bolts of fastening of a cover of the oil pump |
6 Nanometers
|
| Bolts of fastening of a safety valve of the oil pump |
30 Nanometers
|
| Bolts of fastening of the mesh filter to the oil pump |
8 Nanometers
|
| Bolts of fastening of the steel oil pallet |
10 Nanometers
|
| Bolts of fastening of the cast oil pallet |
8 Nanometers
|
| Drain stopper in the steel pallet |
55 Nanometers
|
| Drain stopper in the cast pallet |
45 Nanometers
|
| The top and bottom casings of a gear belt |
4 Nanometers
|
| Back casing of a gear belt |
12 Nanometers
|
| The mechanism of a tension of a gear belt |
20 Nanometers
|