Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
- 3. Engines
   - 3.1. Repair of engine SOCH established in the car
      3.1.1. Introduction
      3.1.2. Technical characteristics
      3.1.3. Check of pressure of compression
      3.1.4. The top dead point (ВМТ) the piston of the first cylinder
      3.1.5. A cover of a head of the block of cylinders
      3.1.6. A pulley of a cranked shaft
      3.1.7. Casings of a gear belt
      3.1.8. A gear belt
      3.1.9. The mechanism of a tension of a gear belt and pulleys
      3.1.10. Replacement of a sealing ring of a cam-shaft
      3.1.11. A cam-shaft and cam-shaft cases
      3.1.12. Hydraulic pushers
      3.1.13. A head of the block of cylinders
      3.1.14. The oil pallet
      3.1.15. The oil pump
      3.1.16. The Flywheel / a drive plate
      3.1.17. Replacement of sealing rings of a cranked shaft
      3.1.18. A suspension bracket of the power unit
   + 3.2. Repair of engine DOSH established in the car
   + 3.3. Repair of the diesel engine of 1,7 l established in the car
   + 3.4. Repair of the diesel engine of 2,0 l established in the car
   + 3.5. Major repairs of engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions


9fd37707

3.1.11. A cam-shaft and cam-shaft cases

Removal

PERFORMANCE ORDER
1. The camshaft can be removed only after removal of the case of a camshaft from the engine. As the camshaft case is attached by bolts of fastening of a head of the block of cylinders, it is necessary to remove a head of the block of cylinders.
2. After removal of the case of a camshaft unscrew a bolt of fastening from the block and remove the block from a case end face.
3. Unscrew bolts and remove a face cover from the left forward end of the case.
4. Measure люфт a camshaft. Unscrew two bolts and remove a persistent plate of a camshaft.
5. Take a camshaft from the left end face of the case of a camshaft.

Check

PERFORMANCE ORDER
1. Check up a condition of bearings in the camshaft case. Check up, that apertures for oil giving to a camshaft have not been hammered.
2. Check up necks and camshaft cams on deterioration.
3. Check up a persistent plate of a camshaft on presence of deterioration and flutes and, if necessary, replace it.

Installation

PERFORMANCE ORDER
1. Remove an old sealing ring of a camshaft and the camshaft case. Establish a new sealing ring working edges inside so that the face surface of a sealing ring was flush with a face surface of the case of a camshaft.
2. Grease a camshaft, bearings of the case of a camshaft and working edges of an oil sealing ring with fresh engine oil.
3. Being careful, establish a camshaft in the camshaft case.
4. Establish a persistent plate of a camshaft and fix its bolts. Check up axial люфт a camshaft.
5. Establish a new sealing ring of round section in a groove of a face cover. Establish a cover to the case of a camshaft and fix bolts.
6. The further installation is made in sequence, return to removal.