Opel Vectra B

Since 1995 of release

Repair and car operation


Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
- 8. Brake system
   8.1. Introduction
   8.2. Technical characteristics
   8.3. Prorolling of hydraulic brake system
   8.4. Brake pipelines and hoses
   8.5. Replacement of lobbies brake колодок
   8.6. Replacement back brake колодок on disk brakes
   8.7. Replacement back brake колодок on drum-type brakes
   8.8. Replacement brake колодок a manual brake
   8.9. Forward and back brake disks
   8.10. A forward brake disk
   8.11. A back brake disk
   8.12. A back brake drum
   8.13. A forward support
   8.14. A back support
   8.15. The back working brake cylinder
   8.16. The main brake cylinder
   8.17. A brake pedal
   8.18. The vacuum amplifier of brakes
   8.19. The unilateral valve of the vacuum amplifier of brakes
   8.20. Adjustment of a manual brake
   8.21. The lever of a manual brake
   8.22. A cable of a manual brake
   8.23. Antiblocking system of brakes (ABS)
   + 8.24. Elements of antiblocking system of brakes
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions



8.8. Replacement brake колодок a manual brake
THE GENERAL DATA

On models with back brake disks the manual brake works irrespective of hydraulic brake system. Are thus used brake Pads drum-type type, and as a brake drum the internal part of a brake disk is used.

Arrangement of a clamp brake Pads a manual brake

Details of the lever of a manual brake

The lever of a manual brake in gathering

PERFORMANCE ORDER
1. Remove a brake disk.
2. Clear a dust and a dirt from a basic plate and brake колодок.
3. Using flat-nose pliers, remove a plate of a spring of fixing brake Pads, pressing a plate and turning it on 90 °.
4. Remove a spring and take a clamp pin.
5. Note an arrangement of all details of a manual brake and remove an adjusting lath from the top part brake колодок.
6. Using flat-nose pliers, remove the top returnable spring with brake колодок.
7. Remove the bottom returnable spring.
8. Remove brake Pads.
9. Using a screw-driver, disconnect a cable of a manual brake from special скобы.
10. Disconnect a returnable spring from a basic plate and remove the lever.
11. Brake Pads a manual brake can be established in sequence, return to removal. However it is the most convenient to establish Pads a manual brake after removal of a back nave. Thus it is necessary to fix temporarily a basic plate two bolts.
12. Collect the lever of a manual brake, putting lubricant on contact surfaces. Then establish the lever to a basic plate, inserting it through a window with rubber consolidation.
13. Establish a cable of a manual brake on the lever.
14. Establish a cable of a manual brake on скобу fastenings.
15. Using flat-nose pliers, clamp скобу fastenings.
16. Then establish a returnable spring.
17. Apply a thin film high-temperature greasing on places of contact brake колодок with a brake board.
18. Establish a lobby колодку.
19. Establish a spring and a plate of fixing brake Pads.
20. Fix a spring and a spring plate.
21. Establish back brake колодку and establish the bottom returnable spring.
22. Establish brake колодку on the bottom basic plate.
23. Establish a spring and a plate of a spring of fastening brake Pads to a brake board.
24. Establish an adjusting lath between the top ends brake колодок.
25. Establish the top returnable spring.
26. Establish a back nave.
27. Temporarily establish a brake disk on brake Pads. Using a screw-driver, turn a regulator nut so that it was possible to remove a brake disk without jamming.
28. Establish a brake disk.
29. Adjust a manual brake.
30. Establish wheels and lower the car.