Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
- 8. Brake system
   8.1. Introduction
   8.2. Technical characteristics
   8.3. Prorolling of hydraulic brake system
   8.4. Brake pipelines and hoses
   8.5. Replacement of lobbies brake колодок
   8.6. Replacement back brake колодок on disk brakes
   8.7. Replacement back brake колодок on drum-type brakes
   8.8. Replacement brake колодок a manual brake
   8.9. Forward and back brake disks
   8.10. A forward brake disk
   8.11. A back brake disk
   8.12. A back brake drum
   8.13. A forward support
   8.14. A back support
   8.15. The back working brake cylinder
   8.16. The main brake cylinder
   8.17. A brake pedal
   8.18. The vacuum amplifier of brakes
   8.19. The unilateral valve of the vacuum amplifier of brakes
   8.20. Adjustment of a manual brake
   8.21. The lever of a manual brake
   8.22. A cable of a manual brake
   8.23. Antiblocking system of brakes (ABS)
   + 8.24. Elements of antiblocking system of brakes
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions



8.5. Replacement of lobbies brake колодок
THE GENERAL DATA

The prevention

Necessarily make replacement of all колодок on one axis of the car even if deterioration borders were reached by one колодка. If Pads will be repeatedly established, before removal they are necessary for marking.

At work brake колодок the brake dust which contains asbestos, unhealthy is formed, therefore at clearing brake колодок do not use compressed air and do not inhale a dust.


PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports. Remove forward wheels.
2. Disconnect an electric socket from the gauge of deterioration brake колодок.
3. From support lateral aspect remove fixing spring.
4. Remove dustproof caps from the internal ends of directing bolts.
5. Unscrew directing bolts of a support.
6. Lift a support with internal колодкой.
7. Using a soft wire, tie up it to a forward rack.
8. Remove internal колодку from the support piston.
9. Remove external колодку from the holder of a support.
10. Clear a dust and a dirt from a support, and a rust from edge of a brake disk.
11. Measure a thickness brake колодок.
12. If Pads are suitable to the further operation, clear them, using a wire brush or rags.
13. Before installation колодок check up that directing bolts easily move in a support.
14. If will be established new brake Pads, press the piston into a support a wooden core or the hammer handle. Thus watch, that the piston has not warped also surfaces of the piston and dusterа have not been damaged. At вдвигании the piston the brake liquid is superseded from the brake cylinder in a broad tank. Therefore constantly observe of liquid level in a tank, and if necessary, pump out from a tank its small amount.
15. Check up that dredging on the support piston are established, as is shown in drawing. If necessary turn the piston in correct position.
16. Establish internal колодку on a support. Thus spring скоба it should be established in piston dredging.
17. Establish external brake колодку.
18. Establish a support with internal колодкой on the holder of a support.
19. Screw in directing bolts of a support and tighten their demanded moment.
20. Establish dustproof caps on directing bolts of a support.
21. Establish fixing spring on a support. Thus the spring ends should settle down in a support aperture.
22. Connect the gauge of deterioration brake колодок.
23. Some times press a brake pedal that brake Pads have nestled on a brake disk. Check up level of a brake liquid in a tank.
24. Repeat the actions set forth above on the second wheel.
25. Establish wheels and lower the car.
26. Check up level of a brake liquid.