Opel Vectra B

Since 1995 of release

Repair and car operation



Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
- 5. Fuel system
   - 5.1. Fuel system of petrol engines
      5.1.1. Introduction
      5.1.2. Technical characteristics
      5.1.3. The air filter and inlet channels
      5.1.4. A control system in temperature of air submitted to the engine
      5.1.5. An accelerator cable
      5.1.6. An accelerator pedal
      5.1.7. Fuel
      + 5.1.8. System of injection of fuel
      5.1.9. Pressure removal in fuel system
      5.1.10. The fuel pump
      5.1.11. The gauge of level of fuel
      5.1.12. A fuel tank
      5.1.13. The throttle case
      5.1.14. Check of system of injection of fuel
      5.1.15. Elements of one-dot system of injection of fuel
      + 5.1.16. Elements of multidot system of injection of fuel
      5.1.17. An inlet collector
      5.1.18. A final collector
      5.1.19. System of release of the fulfilled gases
   + 5.2. Fuel systems of the diesel engine
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions


9fd37707

5.1.17. An inlet collector

Removal and installation

PERFORMANCE ORDER
Engines SOCH of 1,6 l
1. Remove pressure in fuel system and remove a wire of weight from the accumulator.
2. Remove auxiliary приводной a belt and merge cooling liquid from cooling system.
3. Remove a casing of the air filter and the inlet air channel.
4. Disconnect hoses from a throttle casing, unscrew screws and remove a casing from the top part of the case of a throttle.
5. Disconnect electric sockets from a potentiometer of a throttle, the engine of management of turns of idling, a fuel atomizer, the gauge of temperature of a cooling liquid and the valve of system of repeated burning of the fulfilled gases.
6. Unscrew a bolt of fastening of the generator on the right side of a collector.
7. Unscrew connecting nuts and remove fuel hoses from the throttle case.
8. Remove скобу fastenings and separate a torso of an accelerator from spherical шарнирного connections. Remove a cover of a cable of an accelerator from an arm.
9. Disconnect a vacuum hose and a ventilation hose картера from the throttle case.
10. Loosen the a collar also remove a hose of a cooling liquid from a back part of a collector.
11. Unscrew a connecting nut and remove a vacuum hose of the vacuum amplifier of brakes from a collector.
12. Check up that all hoses are disconnected, and unscrew nuts of fastening of a collector.
13. Remove an inlet collector.
14. Installation is made in sequence, return to removal, thus it is necessary to establish a new lining of an inlet collector.
Engines DOCH of 1,6 l
15. Unscrew bolts of fastening of a plastic arm of a plait of wires in a back part of an inlet collector.
16. Disconnect electric sockets from gauges of oxygen, the block of ignition, the valve of clearing and other sockets on the left forward party of a collector. Unscrew a nut of fastening of the tyre of grounding to a head of the block of cylinders and a collector.
17. Remove the valve of catching of steams of fuel (it is specified by an arrow) from the left forward end of a collector and disconnect a hose of the valve from a collector.
18. Unscrew a connecting nut and remove a vacuum hose of the vacuum amplifier of brakes of a collector. Disconnect from a collector a vacuum hose and a ventilation hose картера the engine.
19. Disconnect a vacuum hose from a pressure regulator.
20. Loosen the collars also remove a hose connecting the case of throttles with the top section of a collector.
21. Unscrew bolts of fastening of the top section of a collector (are specified by arrows). Remove the top section of a collector and a lining.
22. For removal of the bottom section of an inlet collector at first remove pressure in fuel system.
23. Unscrew connecting nuts and disconnect fuel hoses from a fuel highway.
24. Loosen the bottom скобу fastenings also remove a connecting part from the case of throttles.
25. Disconnect an electric socket from the gauge of a cranked shaft and release it from a collector.
26. Remove a torso of an accelerator from the case of throttles and disconnect electric sockets from the engine operating turns of idling, and a throttle potentiometer.
27. Unscrew bolts and remove the case of throttles.
28. Unscrew bolts from ledges of an arm of the case of throttles and remove an arm from a collector.
29. Remove auxiliary приводной a belt and unscrew a bolt of fastening of the generator to the right party of a collector.
30. Unscrew nuts and remove the bottom section of a collector.
31. Installation is made in sequence, return to removal. Thus it is necessary to establish a new lining of an inlet collector, to fill in cooling liquid in system of cooling and to adjust an accelerator torso.
Engines of 1,8 and 2,0 l
32. Remove auxiliary приводной a belt.
33. Remove pressure in fuel system and remove a wire of weight from the accumulator.
34. Disconnect electric sockets from the gauge of temperature of air arriving in the engine and a measuring instrument of a stream of air.
35. Loosen the a collar also remove a ventilation hose картера the engine from a back part of a cover of a head of the block of cylinders.
36. Loosen the collars also remove the inlet air channel from the air filter and the case of throttles.
37. Remove скобу fastenings and separate a cable of an accelerator from spherical шарнирного connections of a cam of a throttle.
38. Unscrew bolts and remove an arm of a cable of an accelerator from the case of throttles.
39. Press hoses of giving of a cooling liquid to a back part of the case of throttles, ослабьте collars and remove both hoses.
40. Remove electric sockets from a potentiometer of a throttle and the spherical engine of management of idling turns.
41. Note an arrangement and disconnect hoses from the case of throttles, then unscrew nuts and remove the case of throttles from an inlet collector.
42. Unscrew connecting nuts and remove fuel hoses from a fuel highway.
43. Disconnect electric sockets from the block of ignition, the valve of clearing, the valve of a collector, the gauge of temperature of a cooling liquid, the valve of repeated burning of the fulfilled gases and the oxygen gauge.
44. Release скобы fastenings and remove a casing with electric wires from a back part of a head of the block of cylinders. Disconnect electric sockets of the gauge of a cranked shaft and the detonation gauge.
45. Unscrew a connecting nut and remove a vacuum hose of the vacuum amplifier of brakes of a collector. Disconnect from a collector a vacuum hose and a ventilation hose картера the engine. Disconnect a vacuum hose from a pressure regulator
46. Unscrew the top bolt of fastening of the generator on the right side of an inlet collector.
47. Unscrew bolts and remove an arm of support of the basis of a collector.
48. Unscrew nuts and remove a collector from the engine.
49. Installation is made in sequence, return to removal.