Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
- 11. An electric equipment
- 11.1. The electric equipment
11.1.1. Introduction
11.1.2. Technical characteristics
11.1.3. Electric chains
11.1.4. Detection of not closed chain
11.1.5. Safety locks and the relay
11.1.6. Switches
11.1.7. Bulbs of external illumination
11.1.8. Bulbs of internal illumination
11.1.9. Devices of external illumination
11.1.10. Adjustment of light of headlights
11.1.11. A combination of devices
11.1.12. Screen wiper levers
11.1.13. The screen wiper and draught engine
11.1.14. The engine of a screen wiper of a back door
11.1.15. Washer
11.1.16. A radio tape recorder
11.1.17. Loudspeakers
11.1.18. A safety pillow
11.1.19. Elements of a pillow of safety
+ 11.2. Electroschemes
+ 12. The basic malfunctions
|
FORWARD ILLUMINATION OF SALON
| PERFORMANCE ORDER
|
|
|
| 1. Being careful, a screw-driver remove from a ceiling a lamp of illumination of salon. |
|
2. Take a bulb from spring contacts. |
| 3. Establish a new bulb in sequence, return to removal. Check up that the bulb is accurately fixed between spring contacts. If it is necessary, preliminary turn in contacts. |
|
BACK BULB OF ILLUMINATION OF SALON
| PERFORMANCE ORDER
|
|
1. Being careful and using a screw-driver, take from a ceiling a back bulb of illumination of salon. Take a bulb from spring contacts. |
| 2. Establish a new bulb in sequence, return to removal. Check up that the bulb is accurately fixed between spring contacts. If it is necessary, preliminary turn in contacts. |
|
LUGGAGE SPACE ILLUMINATION
| PERFORMANCE ORDER
|
|
1. Being careful and using a screw-driver, remove a bulb of illumination of a luggage space. |
|
2. Take a bulb from spring contacts. |
| 3. Establish a new bulb in sequence, return to removal. Check up that the bulb is accurately fixed between spring contacts. If it is necessary, preliminary turn in contacts. |
|
BULBS OF THE COMBINATION OF DEVICES
| PERFORMANCE ORDER
|
| 1. Remove a combination of devices. |
|
|
| 2. For bulb removal накаливания turn a cartridge of a bulb and take it from a combination of devices (in a photo at the left – removal of a small cartridge, on the right – big). |
|
3. Take a bulb from a cartridge, having pulled it on itself. Pay attention that some bulbs cannot be taken from cartridges. |
| 4. Establish a new bulb in sequence, return to removal. |
|
ILLUMINATION OF THE SWITCH OF ILLUMINATION
| PERFORMANCE ORDER
|
| 1. Remove the illumination switch. |
|
2. Using a screw-driver, turn a cartridge of a bulb and take it from a back part of the switch of illumination. |
| 3. Establish a new bulb in sequence, return to removal. |
|
BULBS OF THE MULTIPURPOSE BLOCK
| PERFORMANCE ORDER
|
| 1. Remove a combination of devices. |
|
|
| 2. Using flat-nose pliers, turn a cartridge with a bulb and take it from a back part of the multipurpose block. |
| 3. Establish a new bulb in sequence, return to removal. |
|
ILLUMINATION OF THE CONTROL PANEL BY THE HEATER
| PERFORMANCE ORDER
|
| 1. Remove the control panel a heater. |
|
2. Take a corresponding lamp, having pulled it on itself from the holder. |
| 3. Establish a new bulb in sequence, return to removal. |
|
|
|