Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
- 11. An electric equipment
- 11.1. The electric equipment
11.1.1. Introduction
11.1.2. Technical characteristics
11.1.3. Electric chains
11.1.4. Detection of not closed chain
11.1.5. Safety locks and the relay
11.1.6. Switches
11.1.7. Bulbs of external illumination
11.1.8. Bulbs of internal illumination
11.1.9. Devices of external illumination
11.1.10. Adjustment of light of headlights
11.1.11. A combination of devices
11.1.12. Screen wiper levers
11.1.13. The screen wiper and draught engine
11.1.14. The engine of a screen wiper of a back door
11.1.15. Washer
11.1.16. A radio tape recorder
11.1.17. Loudspeakers
11.1.18. A safety pillow
11.1.19. Elements of a pillow of safety
+ 11.2. Electroschemes
+ 12. The basic malfunctions
|
SAFETY PILLOW FROM OUTSIDE THE DRIVER
Safety pillow – an integral part of the central part of a steering wheel.
| PERFORMANCE ORDER
|
| 1. Deactivate system of a pillow of safety. |
| 2. Establish forward wheels for movement directly forward. |
| 3. Unscrew two screws located from the back party of a steering wheel and raise a pillow of safety from a steering wheel. |
|
4. Disconnect an electric socket from a safety pillow. |
| 5. Installation is made in sequence, return to removal. |
|
CONTACT OF THE PILLOW OF SAFETY
| PERFORMANCE ORDER
|
| 1. Remove an air cushion of the driver. |
| 2. Remove a steering wheel. |
| 3. Remove casings of a steering column. |
| 4. Using a small screw-driver, lift an emphasis, then disconnect wire contact. |
|
5. Release 4 back скобы. |
|
6. Remove the block of contact from the top part of a steering column. Check up that halves of the block of contact remain in the central position and arrows are established in the basis. |
|
7. Before installation of the block of contact check up that it is in the central position. Press a clamp on the top part of the block and turn an internal part of the block counter-clockwise before occurrence of obvious resistance. Now turn an internal part of the block of contact on 1,5 turns clockwise and combine arrows of the central part and the block case. |
| 8. If the new block of contact is established, at first remove transport скобу. |
|
9. Establish the block of contacts on a steering column and press it before fixing скобами fastenings. |
| 10. Connect electroconducting by emphasis pressing. |
| 11. Establish casings of a steering column. |
| 12. Establish a steering wheel. |
| 13. Establish a safety pillow. |
|
THE ELECTRONIC CONTROL DEVICE
| PERFORMANCE ORDER
|
| 1. Deactivate system of a pillow of safety. |
| 2. Remove the central console. |
|
|
3. Disconnect an electric socket from the management block, then unscrew nuts and remove the block from an internal part of the car. |
| 4. Installation is made in sequence, return to removal. |
|
THE LATERAL GAUGE OF THE PILLOW OF SAFETY
| PERFORMANCE ORDER
|
| 1. Deactivate system of a pillow of safety. |
| 2. Remove an upholstery of a forward door. |
| 3. Remove a protective film from a forward door for access to the gauge. |
| 4. Disconnect an electric socket, unscrew bolts and remove the gauge. |
| 5. Installation is made in sequence, return to removal. |
|
|
|