Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
- 11. An electric equipment
- 11.1. The electric equipment
11.1.1. Introduction
11.1.2. Technical characteristics
11.1.3. Electric chains
11.1.4. Detection of not closed chain
11.1.5. Safety locks and the relay
11.1.6. Switches
11.1.7. Bulbs of external illumination
11.1.8. Bulbs of internal illumination
11.1.9. Devices of external illumination
11.1.10. Adjustment of light of headlights
11.1.11. A combination of devices
11.1.12. Screen wiper levers
11.1.13. The screen wiper and draught engine
11.1.14. The engine of a screen wiper of a back door
11.1.15. Washer
11.1.16. A radio tape recorder
11.1.17. Loudspeakers
11.1.18. A safety pillow
11.1.19. Elements of a pillow of safety
+ 11.2. Electroschemes
+ 12. The basic malfunctions
|
Before replacement of a bulb of external illumination check up a corresponding electric chain and a safety lock. Do not concern a glass flask of a lamp barehanded. The fingerprint evaporates and besieged on a reflector therefore illumination worsens. Necessarily replace the failed lamps with lamps of the same type. Stains arising on imprudence from touches wipe pure безворсовой a rag or spirit.
HEADLIGHTS
PERFORMANCE ORDER
|
|
1. Open a cowl and remove a back cover from a headlight. Pay attention that an internal headlight for a passing light, and an external headlight for a headlight. At work on the left headlight it is necessary to remove the block of the relay from a forward part of the accumulator temporarily. |
|
|
2. Remove an electric socket from a bulb of a headlight distant and a passing light. |
|
3. Compress spring скобы fastenings of a bulb and move скобы aside. |
|
4. Take a lamp from a headlight headlight. |
|
5. Release скобы fastenings of a bulb of a headlight of a passing light. |
|
6. Remove a bulb from a passing light headlight. |
7. Establish a new bulb in sequence, return to removal. |
|
FORWARD DIMENSIONAL LANTERN
PERFORMANCE ORDER
|
1. The lamp of a dimensional forward lantern is located in a headlight headlight. Remove a back cover from a headlight. |
|
2. Take a cartridge with a bulb of a dimensional lantern from a back part of a headlight. |
3. Take a bulb from a cartridge. |
4. Establish a new bulb in sequence, return to removal. |
|
THE FORWARD INDEX OF TURNS
PERFORMANCE ORDER
|
1. Open a cowl and a screw-driver release top скобу fastenings from a headlight outer side. |
2. Take the forward index of turns forward from grooves in a headlight. |
|
3. Turn a cartridge with a bulb and take it from the forward index of turns. |
|
4. Press and turn a bulb for its extraction from a cartridge. |
5. Establish a new bulb in sequence, return to removal. |
|
FORWARD ANTIFOG HEADLIGHT
PERFORMANCE ORDER
|
1. Uncover a back part of the antifog headlight located in a forward bumper. |
2. Disconnect an electric socket, ослабьте скобу fastenings and take a bulb with an antifog headlight. |
3. Establish a new bulb in sequence, return to removal. |
|
THE LATERAL REPEATER OF TURNS
PERFORMANCE ORDER
|
|
1. Using an edge of a thin screw-driver as the lever, take the lateral repeater of turns from an overlay of a forward wing. |
|
2. Keeping a bulb cartridge, turn the lateral repeater of turns and remove it from a cartridge. |
|
3. Take from a cartridge a bulb, having pulled it on itself. |
4. Establish a new bulb in sequence, return to removal. |
|
BACK LANTERNS
PERFORMANCE ORDER
|
1. Remove the furnish of a luggage space located opposite to back lanterns. |
|
2. Press fixing uvula in the middle of the holder of bulbs of a back lantern and take the holder of bulbs from a lantern. |
|
3. Press and turn a bulb and take it from the holder of bulbs. |
4. Establish a new bulb in sequence, return to removal. |
|
LANTERN OF ILLUMINATION OF LICENSE PLATE
PERFORMANCE ORDER
|
1. Open a luggage carrier or a back door, then insert an edge of a thin screw-driver vertically between a right edge of a lantern of illumination of licence plate and a back bumper. Loosen the a clamp also take a lantern of illumination of licence plate upwards from a bumper. |
2. Press скобу fastenings and remove a plafond from a lantern of illumination of licence plate. |
3. Press and turn a bulb for its removal from a cartridge. |
4. Installation of a new bulb is made in sequence, return to removal. |
|
THE TOP STOPLIGHT
PERFORMANCE ORDER
|
1. Open a back door and remove an upholstery of furnish of a back part of salon. |
|
2. Remove заглушки, closing screws. |
|
3. Unscrew screws and remove a frame together with the top stoplight. |
|
4. Separate from a frame a stoplight lantern. |
|
5. Remove a casing from the holder of bulbs |
|
6. Using a screw-driver, release clamps |
|
7. Remove a strip with lamps накаливания from the holder. |
|
8. Disconnect an electric socket and remove a strip with bulbs накаливания. |
9. Installation is made in sequence, return to removal. |
|
|
|