Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
- 3. Engines
+ 3.1. Repair of engine SOCH established in the car
- 3.2. Repair of engine DOSH established in the car
3.2.1. Introduction
3.2.2. Technical characteristics
3.2.3. Compression check
3.2.4. The top dead point (ВМТ) the piston of the first cylinder
3.2.5. A cover of a head of the block of cylinders
3.2.6. A pulley of a cranked shaft
3.2.7. Casings of a gear belt
3.2.8. A gear belt
3.2.9. Pulleys of a gear belt, the mechanism of a tension and a single pulley
3.2.10. Replacement of oil sealing rings of a cam-shaft
3.2.11. A cam-shaft and pushers
3.2.12. A head of the block of cylinders
3.2.13. The oil pallet
3.2.14. The oil pump
3.2.15. The Flywheel / a drive plate
3.2.16. Replacement of oil sealing rings of a cranked shaft
3.2.17. A suspension bracket of the power unit
+ 3.3. Repair of the diesel engine of 1,7 l established in the car
+ 3.4. Repair of the diesel engine of 2,0 l established in the car
+ 3.5. Major repairs of engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions
|
Removal
ENGINES OF 1,6 L
| PERFORMANCE ORDER
|
| The top casing |
| 1. Remove a casing of the air filter. |
|
|
2. Unscrew screws of fastening of the top casing of a gear belt to a back casing and take it from a motor compartment. |
| 3. Installation is made in sequence, return to removal. |
| The bottom casing |
| 4. Remove the top casing. |
| 5. Remove a pulley of a cranked shaft. |
|
|
| 6. Unscrew bolts of fastening of the bottom casing to a back casing and take it from the car (on a photo at the left – the top bolt of fastening of the bottom casing, on the right – the bottom bolt of fastening). |
| 7. Installation is made in sequence, return to removal. |
| Back casing |
| 8. Remove a gear belt. |
| 9. Remove pulleys of camshafts, a pulley of a cranked shaft, the mechanism of a tension of a gear belt and a back single pulley. |
|
10. Unscrew fastening bolts (are specified by arrows) and remove a back casing of a gear belt. |
| 11. Installation is made in sequence, return to removal. |
|
ENGINES OF 1,8 AND 2,0 L
| PERFORMANCE ORDER
|
| External casing |
| 12. Remove a casing of the air filter. |
| 13. Remove auxiliary приводной a belt |
| 14. Unscrew bolts of fastening of draught of the jack of a twisting moment to an arm of the engine and remove it from the right end of the engine. |
|
|
| 15. Unscrew fastening bolts, remove rubber proluggage under bolts and remove an external casing of a gear belt. |
| 16. Installation is made in sequence, return to removal. |
|
17. Establish consolidation on an external casing of a gear belt. |
| Back casing |
| 18. Remove a gear belt. |
| 19. Remove pulleys of camshafts, a pulley of a cranked shaft, the mechanism of a tension of a gear belt and an idling pulley. |
| 20. Unscrew a bolt of fastening of the gauge of a camshaft. |
| 21. Unscrew bolts of fastening of draught of the jack of a twisting moment from an end face of a head of the block of cylinders. |
| 22. Unscrew bolts and remove a back casing of a gear belt. |
| 23. Unscrew bolts and remove a back casing of a gear belt. |
|
|
|