Opel of Vektra
+ 1.1. Controls and control devices
+ 2. Maintenance service
- 3. Engines
+ 3.1. Repair of engine SOCH established in the car
- 3.2. Repair of engine DOSH established in the car
3.2.1. Introduction
3.2.2. Technical characteristics
3.2.3. Compression check
3.2.4. The top dead point (ВМТ) the piston of the first cylinder
3.2.5. A cover of a head of the block of cylinders
3.2.6. A pulley of a cranked shaft
3.2.7. Casings of a gear belt
3.2.8. A gear belt
3.2.9. Pulleys of a gear belt, the mechanism of a tension and a single pulley
3.2.10. Replacement of oil sealing rings of a cam-shaft
3.2.11. A cam-shaft and pushers
3.2.12. A head of the block of cylinders
3.2.13. The oil pallet
3.2.14. The oil pump
3.2.15. The Flywheel / a drive plate
3.2.16. Replacement of oil sealing rings of a cranked shaft
3.2.17. A suspension bracket of the power unit
+ 3.3. Repair of the diesel engine of 1,7 l established in the car
+ 3.4. Repair of the diesel engine of 2,0 l established in the car
+ 3.5. Major repairs of engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Systems of start, ignition
+ 7. Transmission
+ 8. Brake system
+ 9. A running gear
+ 10. A body
+ 11. An electric equipment
+ 12. The basic malfunctions
|
Sequence of numbering of covers of bearings of camshafts
Arrangement of labels of identification on covers of bearings of camshafts and on a head of the block of cylinders
Places of drawing of a thin layer of hermetic on a head of the block of the cylinders interfaced to the right covers of bearings of a camshaft
Removal
PERFORMANCE ORDER
|
|
1. Remove a gear belt. Before removal of a gear belt turn a cranked shaft in the opposite direction approximately on 60 ° (4 teeth) that will establish camshafts so that pressure клапанных springs will be in regular intervals on all length of a shaft. |
2. Remove pulleys from camshafts. |
3. On distributive to a shaft, operating inlet valves, working in spiral sequence outside inside, in regular intervals and gradually ослабьте bolts of fastening of covers of bearings rasprede-litelnogo a shaft. As soon as pressure клапанной springs will stop, unscrew bolts completely. Covers of bearings and a place of their installation on a head of the block of cylinders are numbered. (A camshaft of inlet valves from 1 to 5. The Camshaft of final valves from 6 to 10). |
|
4. Take a camshaft from a head of the block of cylinders. |
5. Repeat actions on removal of the camshaft operating final valves. |
|
6. Using a rubber sucker, take pushers from the top part of a head of the block of cylinders and store each pusher in a separate package for the subsequent repeated installation of pushers on the places. |
The prevention
Do not overturn hydraulic pushers as from them oil can flow out.
|
|
Check
PERFORMANCE ORDER
|
1. Check up working surfaces of bearings of camshafts and contours of cams of camshafts on deterioration. In the presence of any deterioration replace a camshaft. If camshaft bearings are worn out, it is necessary to replace a head of the block of the cylinder. |
2. Check up a condition of working surfaces hydraulic tolkate-pour, which contact with camshaft cams. |
|
Installation
PERFORMANCE ORDER
|
1. Grease hydraulic pushers with pure engine oil and insert each pusher on the place in a head of the block of cylinders. |
2. Grease necks and camshaft cams with pure engine oil and establish a camshaft in a head of the block of cylinders. Check up that the cranked shaft is in position on 60 ° back from the top dead point of the first cylinder, and turn each camshaft so that ledges of cams of the first cylinder have been directed upwards. Temporarily establish pulleys on camshafts and turn them so that the adjusting label of a pulley has been displaced on 4 teeth before ВМТ. |
3. Apply a thin film hermetic to interfaced surfaces of the right covers of bearings of camshafts (fig. of the Place of drawing of a thin layer of hermetic on a head of the block of the cylinders interfaced to the right covers of bearings of a camshaft) see. |
|
4. Establish covers of bearings according to identification labels. |
|
5. On distributive to a shaft, operating inlet valves, tighten bolts of fastening of covers of bearings of a camshaft a hand, then on a spiral from the centre to edge tighten bolts of fastening of covers of bearings gradually and in certain sequence, turning each bolt on half of turn for one pass until each cover will not concern heads of the block of cylinders. Then in the same sequence tighten bolts the demanded moment in some stages. |
|
6. Similarly tighten bolts of fastening of covers of bearings of the camshaft operating final valves. |
7. Establish new oil sealing rings of camshafts. |
8. Establish pulleys of camshafts. |
9. Combine all adjusting labels of pulleys with indexes and establish a gear belt. |
10. Establish a cover of a head of the block of cylinders and casings of a gear belt. |
|
|
|